18600BSTM
Self contained refrigerated work top table with backsplash
- Work tables have a stainless steel exterior standard.
- The compressor is located on the right side of the unit.
- Full finished stainless steel ends and top.
Width : -
Depth : -
Height : -
Specification Sheet
DS18BSTM
18600BUCM
Self contained refrigerated work top table
- Work tables have a stainless steel exterior standard.
- The compressor is located on the right side of the unit.
- Full finished stainless steel ends and top.
Width : -
Depth : -
Height : -
Specification Sheet
DS18BUCM
CTP-NB Standard
Counter top condiment rail
- Unit Interior : has a 22-gauge stainless steel liner with foamed-in-place polyurethane insulation.
- Base : of unit has removable louvers at front and rear for proper air flow and access to the condensing unit. Protective rubber bumpers are affixed to the back of the unit.
- Refrigeration System : uses HFC-134a refrigerant. Refrigerated rail is designed to maintain41°F (5°C) at 85°F ambient, 50% relative humidity for up to (4) hours when pans are recessed 3" (7.6 cm) below top. Food and product should be placed in unit at 37°F (3°C). On/off switch is located at front of unit.
Width : 277/8"
Depth : 17"
Height : 17"
Specification Sheet
DSCTPNB
F17C
Self-Contained Refrigerated Base Equipment Stands
- Refrigerated Base : Refrigerated base interior back and bottom is constructed of 22-gauge 2BF stainless steel. Exterior sides are constructed of 18-gauge stainless steel. Bottom and back are made of 22 gauge galvanized steel. Both left and right interior sides are formed of ABS plastic. The base is injected with 2.00" of high density polyurethane foam between the exterior and interior. Refrigerated base fronts are made of .095" thick ABS thermoformed plastic and backed up by ridged polyurethane water blown injection molded frames. The frames are an excellent thermo-break and superior structural material for fastening doors and drawers. Exterior machine compartment side is constructed of 18-gauge galvanized steel.
- Bracket : Single units are supplied with wall-mounted bracket and threaded rod to allow installation of the unit against a solid surface. Units shipped, as part of a line-up do not come standard with a wall mounted bracket assembly.
- Drawer System : Full Extension Plus drawer system is a complete drawer system, which can operate independent of the unit itÂÂ’s installed in. Drawer system is sized to hold 12 x 20 x 4 “ deep hotel pans and smaller fractional pans. Drawer system is all stainless steel construction for maximum durability. Outer drawer track is made of 11-gauge stainless and held in place with 12-gauge up-right and cross supports. Drawer track rollers are made of Delrin™ 100 NC-10 and do not require grease for operation. Intermediate tracks are removable without tools and house DelfieldÂÂ’s “anti-friction binary roller system". Drawer boxes are designed with “easy pan grip flanges". Tracks are designed with a stay shut feature that holds the drawer gasket tight to the base front on uneven floors. Exterior drawer fronts are made of 22- gauge stainless steel; and an interior made of ABS plastic with formed in channels to house the snap-in dart style santoprene gasket. A 12-gauge galvanized brace is foamed in place to be an integral part of the drawer front assembly. Each drawer front is injected with 1.87" of high density polyurethane foam between the exterior and interior. Handles are recessed black plastic and held in with a positive lock system.
Width : 52"
Depth : 303/4"
Height : 40"
Specification Sheet
DSF17C
F17R
Remote Refrigerated Base Equipment Stands
- Refrigerated Base : Refrigerated base interior back and bottom is constructed of 22-gauge 2BF stainless steel. Exterior sides are made of 18-gauge stainless steel. Bottom and back are made of 22 gauge galvanized steel. Both left and right interior sides are formed of ABS plastic. The base is injected with 2.00" of high density polyurethane foam between the exterior and interior. Refrigerated base fronts are made of .095" thick ABS thermoformed plastic and backed up by ridged polyurethane water blown injection molded frames. The frames are an excellent thermobreak and superior structural material for fastening doors and drawers. Exterior machine compartment side is constructed with 18-gauge galvanized steel.
- Single Units : Single units are supplied with a wall-mounted bracket and threaded rod to allow installation of the unit against a solid surface. Units shipped as part of a line-up do not come standard with a wall mounted bracket assembly.
- Drawer System : Full Extension Plus drawer system is a complete drawer system, which can operate independent of the unit itÂÂs installed in. Drawer system is sized to hold 12 x 20 x 4 ÂÂ deep hotel pans and smaller fractional pans. Drawer system is all stainless steel construction for maximum durability. Outer drawer track is made of 11-gauge stainless and held in place with 12-gauge up right and cross supports. Drawer track rollers are made of DelrinÂÂ 100 NC-10 and do not require grease for operation. Intermediate tracks are removable without tools and house DelfieldÂÂs ÂÂanti-friction binary roller system". Drawer boxes are designed with ÂÂeasy pan grip flanges". Tracks are designed with a stay shut feature that holds the drawer gasket tight to the base front on uneven floors. Exterior drawer fronts are made of 22- gauge stainless steel; and an interior made of ABS plastic with formed in channels to house the snap-in dart style santoprene gasket. A 12-gauge galvanized brace is foamed in place to be an integral part of the drawer front assembly. Each drawer front is injected with 1.87" of high density polyurethane foam between the exterior and interior. Handles are recessed black plastic and held in with a positive lock system.
Width : 44"
Depth : 303/4"
Height : 40"
Specification Sheet
DSF17R
F18DC
31.5" (80cm) Deep Self-Contained Quick Glance Rail
- Construction : Exterior Back and Bottom are 24-gauge galvanized steel. Exterior ends are finished with 18-gauge galvanized steel.
- Base Interior : Base Interior has 22-gauge stainless steel back and bottom. Base interior ends and door frames are thermoformed ABS plastic. Base is insulated with 1.5" (3.8cm) high density foamed in place polyurethane. End of base has a machine compartment, standard on right, with condensing unit installed.
- Doors : Door(s) have a 22-gauge stainless steel exterior front, with thermoformed ABS plastic interior liner, black recessed handle and snap in magnetic gasket which is easily replaceable. Each interior door section has (1) removable epoxy coated wire shelf.
Width : 52"
Depth : 311/2"
Height : 433/4"
Specification Sheet
DSF18DC
F18DR
31.5" (80cm) Deep Remote Quick Glance Rail
- Construction : Exterior Back and Bottom are 24-gauge galvanized steel. Exterior ends are finished with 18-gauge galvanized steel.
- Base Interior : Base Interior has 22-gauge stainless steel back and bottom. Base interior ends and door frames are thermoformed ABS plastic. Base is insulated with 1.5" (3.8cm) high density foamed in place polyurethane. End of base has a machine compartment, standard on right, with condensing unit installed.
- Doors : Door(s) have a 22-gauge stainless steel exterior front, with thermoformed ABS plastic interior liner, black recessed handle and snap in magnetic gasket which is easily replaceable. Each interior door section has (1) removable epoxy coated wire shelf.
Width : 44"
Depth : 311/2"
Height : 433/4"
Specification Sheet
DSF18DR
F18RC
31.5" (80cm) Deep Self-Contained Refrigerated Reduced Height Rail
- Construction : Exterior back and bottom are 24-gauge galvanized steel. Exterior ends are 18-gauge galvanized steel.
- Base Interior : Base Interior has 22-gauge stainless steel back and bottom. Base interior ends and door frames are thermoformed ABS plastic. Base is insulated with 1.5" (3.8cm) high density foamed in place polyurethane. End of base has a machine compartment, standard on right, with condensing unit installed.
- Doors : Door(s) have a 22-gauge stainless steel exterior front, with a thermoformed ABS plastic interior liner. Door(s) have a black recessed handle and a snap-in magnetic gasket which is easily replaceable.
Width : 52"
Depth : 311/2"
Height : 42"
Specification Sheet
DSF18RC
F18RR
31.5" (80cm) Deep Remote Reduced Height Rail
- Construction : Exterior back and bottom are 24-gauge galvanized steel. Exterior ends are 18-gauge galvanized steel.
- Base Interior : Base Interior is 22-gauge stainless steel back and bottom. Base interior ends and door frames are thermoformed ABS plastic. Base is insulated with 1.5" (3.8cm) high density foamed in place polyurethane.
- Doors : Door(s) have a 22-gauge stainless steel exterior front, with a thermoformed ABS plastic interior liner. Door(s) have a black recessed handle and a snap-in magnetic gasket which is easily replaceable.
Width : 44"
Depth : 311/2"
Height : 42"
Specification Sheet
DSF18RR
F18WC
31.5" (80cm) Deep Self-Contained Refrigerated Work Tables
- Construction : Exterior back and bottom to be 24-gauge galvanized steel. Exterior ends are 18-gauge galvanized steel.
- Base Interior : Base Interior is 22-gauge stainless steel back and bottom. Base interior ends and door frames are thermoformed ABS plastic. Base is insulated with 1.5" (3.8cm) high density foamed in place polyurethane.
- Doors : Door(s) have a 22-gauge stainless steel exterior front, with a thermoformed ABS plastic interior liner. Door(s) have black recessed handle(s) and a snap-in magnetic gasket which is easily replaceable. Each interior door section has (1) removable epoxy-coated wire shelf.
Width : 39"
Depth : 311/2"
Height : 40"
Specification Sheet
DSF18WC
F18WR
31.5" (80cm) Deep Remote Refrigerated Work Tables
- Construction : Exterior back and bottom to be 24-gauge galvanized steel. Exterior ends are 18-gauge galvanized steel.
- Base Interior : Base Interior is 22-gauge stainless steel back and bottom. Base interior ends and door frames are thermoformed ABS plastic. Base is insulated with 1.5" (3.8cm) high density foamed in place polyurethane.
- Doors : Door(s) have a thermoformed plastic ABS plastic interior liner and 22- gauge stainless steel exterior front. Door(s) have black recessed handle(s) and a snap-in magnetic gasket which is easily replaceable. Unit is furnished with (1) epoxy coated wire shelf for each door section.
Width : 31"
Depth : 311/2"
Height : 40"
Specification Sheet
DSF18WR
F2800, F2900C
Low-Profile Refrigerated Base Equipment Stands
- Refrigerated Base : Refrigerated base has 22 gauge stainless steel interior back and bottom with ABS thermoformed sides. Base exterior back, bottom and sides are constructed of galvanized steel.
- Stainless Steel Ends : Finished stainless steel ends are standard. Louver, coil panel and drawer faces are all standard with stainless steel construction. (Unit is supplied with a wall-mounted bracket and threaded rod to allow installation of the unit against a solid surface.)
- Legs/Casters : Units foundation is made of 14 gauge 1.50" x 3.25" thick galvanized leg rails with casters as standard. Unit comes standard with a stainless steel leg rail cover-up skin. Legs available on request.
Width : 521/4"
Depth : 31"
Height : 26"
.jpg "ST4048")
ST4048
Self-contained compact work top refrigerators
- All ST4048 refrigerators feature Delfield's exclusive ABS interior. ABS is extremely durable - it won't dent, chip or corrode and is backed by a limited lifetime warranty.
- Units are constructed of stainless steel front, sides and top.
- All units use environmentally friendly R404A refrigerant.
Width : 48"
Depth : 285/16"
Height : 391/2"
Specification Sheet
DSST4000