Versatile, High Performance Units Designed to work in the real world.
Our 4400 series prep tables provide an integrated design solution to your salad, sandwich and other meal preparation needs. Designed to be easy to work from, they provide a compact area where storage and assembly areas are combined to create an efficient production system. Labor productivity is high. Operational costs are low. Food is kept at safe, consistent temperatures, keeping your meal quality high and your food waste costs low.
Reduced Height Front-Breathing Self-Contained Compact Mega Top Refrigerators
|Width x Depth x Height||481/8"
(122.24 cm x 80.01 cm x 87.00 cm)
|Power Output||7.2 Amps|
|Exterior Top||Exterior top is one-piece 22-gauge stainless steel with integral 2.12” (5.4cm) square nosing on the front. Top of drawer unit has openings to accept eighteen 1/6 size plastic pans 4” (10cm) deep. Top of door unit has openings to accept eighteen 1/6 size plastic pans 4” or 6” (10cm or 15cm) deep. Adapter bars and 1/6 size pans are supplied by Delfield. Top has one telescoping lid, constructed of 20-gauge stainless steel. Temperature in top openings maintains 33°F (1°C) to 41°F (5°C), with pans recessed 2.5” (6.4cm) at 86°F ambient room temperature, meeting NSF 7 requirements. One 48” x 8” x .5” (121.9cm x 20.3cm x 1.3cm) polyethylene cutting board treated with antimicrobial agent is mounted on the top at the front edge.|
|Exterior Sides and Back||Exterior back and bottom are two-piece 24-gauge galvanized steel. Exterior ends are stainless steel.|
|Interior Sides||Interior sides are thermoformed ABS plastic with integral shelf supports. Base is fully insulated with high-density foamed in place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane.|
|Refrigeration System||Refrigeration system uses HFC-404A refrigerant. Compressor is 1/5 H.P., with condenser coil and hot gas condensate evaporator mounted on rear of the cabinet. Evaporator coil is located on the interior rear wall of the cabinet. Refrigerant flow is controlled by a capillary tube. Cabinet maintains an interior cabinet temperature of 36°F to 40°F (2°C to 4°C).|
|ACT Control||ACT electronic, solid state control, mounted on the exterior rear of the cabinet, allows unit to maintain precise temperatures in heavy duty conditions.|
|Electrical Connections||Electrical connections are 115 volt, 60 Hertz, single phase. Unit has a 6’ (1.8m) long electrical cord and NEMA 5-15P plug.|
|Casters||Equipment is mounted on 3” (7.6cm) diameter plate casters. Equipment clearance above the floor is 0.66” (1.7cm).|
|Doors||Doors have a 24-gauge stainless steel exterior, with thermoformed ABS plastic interior liner. Cabinet has one adjustable epoxy-coated wire shelf per door opening.|
|Drawers||Drawers have 24-gauge stainless steel exterior with thermoformed ABS plastic interior liner. Drawer frames are 12-gauge stainless steel. Drawer slides are 11-gauge stainless steel with Delrin bearings. Each top drawer will hold one 12” x 20” (30.5cm x 50.8cm) pan and three 1/9 size 4”-6” (10.2cm-15.2cm) deep pans. Each bottom drawer holds one 12” x 20” (30.5cm x 50.8cm) pan and three 1/9 size 4” (10.2cm) deep pans. Pans are supplied by others.|
|Dual level pan brackets||Dual level pan brackets allow the pans to be lowered an additional inch in the unit without tools to provide additional pan temperature holding performance.|
|Energy Use||8.11 KWh daily|